background image

VENTING 

25

SP-41-L MANUAL REV#2 OCT 2017

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

7.6  #700-2 Series Direct Vent 

Termination Kit(s)

IMPORTANT: The vertical vent heat shield included with this 
fireplace must be installed for every type of venting application. 
IMPORTANT: Wall pass-through products (G) with the required  
minimum 1 in (25 mm) clearance on all sides of the horizontal 
vent pipe must be fully lined with unfaced insulation products 
listed as noncombustible per ASTM E 136.
IMPORTANT: The minimum bend radius to center is 6 in (152 
mm) required for installation of the flexible vent pipe. Care 
should be taken when installing the flexible vent pipe to avoid 
a tight bend that may cause abrasion or damage to the flexible 
pipe. 
IMPORTANT: The flex pipe is permanently attached to the 
exterior plate. DO NOT ATTACH either #745-2 or #718-2 
termination kit to fireplace (or extension kit) until it has passed 
through the wall. Install termination plates to the outside wall 
exterior.

•  If terminating against vinyl siding, a vinyl siding protector 

must be used (included with the #745-2 and #718-2 direct 
vent kits). Follow instructions included. 

•  Each #746-2 extension kit contains enough 4” & 7” flexible 

aluminum pipe to extend chimney an additional 6 ft (1.83 m). 

7.6.1  Assembly and Installation

1.  Fully line the wall pass-through with any unfaced insulation 

products listed as non-combustible per ASTM E 136. Do not 
proceed with installation until wall pass-through is insulated.

2.  Mount the required wall pass-through (G) to the exterior wall, 

and seal.

3.  Apply a liberal bead of exterior sealant around outer edge of 

termination box (A), placing assembly through the wall-pass 
through in exterior wall. Place screws through the four holes 
(B), securing it in place.

4.  Form the 4” & 7” flexible aluminum pipes on termination kit 

(#745-2 or #718-2), and if applicable, on each extension kit. 

5.  Gently pull 4” & 7” pipes down to the top of the fireplace, or if 

applicable, the extension kit.  

IMPORTANT: DO NOT stretch extension kit beyond 6 ft. 
(1.83 m); DO NOT stretch beyond what is required. It is 
very difficult to decompress flex pipes once stretched. 

6.  Place a bead of sealant outside 4” flex pipe collar (C) (end 

with EXTERNAL LIP) and sliding it into 4” pipe on extension 
kit or top of fireplace (D). Secure with 3 evenly spaced 
screws.

7.  Place a bead of sealant inside 7” flex pipe collar (E) (end 

with the INTERNAL lip), sliding it over 7” pipe on top of 
fireplace (F). Secure with 3 evenly spaced screws. 

8.  If additional extension kits are required, repeat Steps 4 and 

5, placing 4” & 7” pipes onto previous extension kit.

LEGEND

A

Termination box

B

Holes in exterior wall plate (only 3 shown)

C

4” flex pipe collar

D

4” pipe on fireplace or extension kit 

E

7” flex pipe collar

F

7” pipe on fireplace or extension kit

G

Wall Pass-Through

Figure 7.3, Installation and Assembly of #700-2 Series (Vent Heat Shield Assembly not shown for clarity purposes only) 

A

B

C

D

E

F

G

Summary of Contents for SP-41 LOG

















































Reviews: