62
REC/Play
: The metronome will sound during recording or
playback.
Off
: The metronome will not sound. However, a pre-count
will be heard before recording begins.
Precount
[0…2]
Specifies the length of the pre-count when recording.
With a setting of 0, recording will start the instant you press
the [F5] (“START”) key after pressing [F4] (“REC”).
Level
[000…127]
Sets the volume of the metronome.
BUS (BUS Select)
[L/R, L, R, 1, 2, 3, 4, 1/2, 3/4]
Specifies the output destination of the metronome sound.
L/R
, L, R: Output from the OUTPUT (MAIN) L/Mono and/
or R jacks.
1
, 2, 3, 4, 1/2, 3/4: Output from the OUTPUT (INDIVIDUAL)
1, 2, 3, 4 jacks respectively.
■
5.1–1c: REC, START/STOP
Realtime-record or play patterns.
Use the [F4] (“REC”) key and [F5] (“START/STOP”) key to
record.
: Normal mode.
: Press the [F4] (“REC”) key to enter record-
ready mode. To cancel recording, press the [F4] (“REC”) key
once again. In record-ready mode, pressing the [F5]
(“START”) key will start recording. At this time, recording
will begin after counting the number of measures specified
by “Precount.”
If you wish to delete previously-recorded data while you
record, press the [F4] (“REC”) key. Data will be deleted as
long as you continue holding down this key. If you wish to
delete specific data
, use “Remove Data” (5.1–1b).
: Playback will start when you press the [F5]
(“START”) key from normal mode.
: Pressing the [F5] (“STOP”) key during
playback will stop playback.
■
5.1–1d: SW1, SW2
This switches the function of SW1 and SW2 on (
) or
off (
). During recording of a pattern/playback, you
can use SW1 and SW2 to control the functions assigned to
them.
■
5.1–1e: UTILITY
☞
“Memory Status,” “Rename Track” (1.1–1c)
For details on how to select the desired utility function, refer
to “PROG 1.1–1d: UTILITY.”
Rename Pattern
Specifies “Rename Pattern” to access the dialog box, and
rename the selected pattern. You may input up to sixteen
characters. (
Step Recording(Loop)
Here you can perform step recording into a pattern.
This is available when a user pattern is selected.
1
In “Pattern Bank” and “Pattern Select,” specify the pat-
tern. By default, the pattern length is one measure. If you
wish to change the number of measures in the pattern,
set the Utility “Pattern Parameter”.
2
Select the “Step Recording (Loop)” to access the dialog
box.
3
In “Meter,” set the time signature.
This will show the time signature that has already been
set for the measure.
If you change the time signature setting, the time signa-
ture data of the measures you record will change.
4
In “Step (Step Time),” specify the length of the basic step
that you wish to input, in terms of a note value. The
number of clocks in each note value is shown below.
5
In “Duration,” specify the length that the note will actu-
ally be held, relative to the “Step.” In general, 100% will
be tenuto, 85% will be normal, and 50% will be staccato.
6
Use “Vel. (Velocity)” to specify the velocity value (key-
board playing strength) of the note data. When the [F7]
(“PAUSE”) key is pressed, you can hold down the
[ENTER] key and play a note on a connected MIDI
instrument to specify the velocity value. If you set this to
Key
, the actual velocity at which you played the key will
be input.
7
Using the keyboard of a connected MIDI instrument or
by selecting parameters at the bottom of the dialog box,
input note events as follows.
• Inputting notes
When you play a note on a connected MIDI instrument,
that note number will be input with the note length that
is specified by
4
.
When you press a chord on the keyboard, those note
numbers will be input as chords of the length specified in
4
. Since each of the note numbers you press before
releasing all of the keys will be input at the same location,
the notes will be input as a chord even if they are actually
played at different times.
Each time you press and release the keyboard, the loca-
tion will advance by the length specified in
4
.
• Inputting rests
Press the [F4] (“Rest”) key to input a rest of the length
specified in
4
.
Note number
Location within the
measure (beat, clock)
Length (beat, clock)
Time signature
Velocity
(0:24)
(0:48)
(0:96)
(1:00)
(2:00)
(4:00)
(0:36)
(0:72)
(0:144)
(1:96)
(3:00)
(6:00)
(0:16)
(0:32)
(0:64)
(0:128)
(1:64)
(2:128)
3
3
3
3
3
3