Korg TRITON Extreme Manual Download

Page: 24 / 354

Program

▼

1–2: Page Menu Command

1–2A: Sample Parameters

Specifies the sample for each index of a RAM multisample.
You can adjust the playback level, cutoff, resonance, pitch,
attack, and decay.

This can be selected if “Oscillator Mode” (1–1a) is Sin-
gle

or Double, and RAM is selected as the “High MS

Bank

” or “Low MS Bank” for OSC1 Multisample or

OSC2 Multisample and “High Multisample” or “Low
Multisample

” are selected.

These settings are made for the selected multisample. If
another oscillator or program uses that multisample,
that oscillator or program will also be affected by the
changes you make here.

Select “Sample Parameters” to access the dialog box.

Index:

Specify the index for which you wish to make set-

tings. The number following “/” is the total number of
indexes in the selected multisample.
Sample:

indicates the sample number and name for the

index.

For each index, you can make the following settings.
Level:

Adjust the volume. Relative to the settings of

“Lvl” (1–2a) and “Amp Level” (4–1a, 4–4), negative (–)
values

will decrease the levels, and positive (+) values

will increase the levels. A setting of +99 will double the
volume. This parameter is linked to the “Level” (Sam-
pling P3: 3–1b). The value that was specified in Sampling
mode will be displayed here.

The volume is also affected by the “+12 dB” (Sampling
P2: 2–1c) setting. If the “+12 dB” setting is on, the play-
back will be approxi12 dB louder.

Cutoff:

Adjusts the filter cutoff. This adjustment will be

added to the value specified for “(Filter A) Frequency”
(3–1b, 3–5) of Filter 1 and 2.
Resonance:

Adjusts the resonance level of the filter. This

adjustment will be added to the value specified for “(Fil-
ter A) Resonance” (3–1b, 3–5) of Filter 1 and 2.
Pitch:

Adjusts the playback pitch in one-cent steps. A set-

ting of +12.00 raises the pitch one octave, and a setting of
–12.00

will lower the pitch one octave. This parameter is

linked with the Sampling P3: Multi Sample parameter
“Pitch” (Sampling P3: 3–1b). The value that was specified
in Sampling mode will be displayed here.
Attack:

Adjusts the attack times of the filter EG and amp

EG. This adjustment will be added to the “(Time) Attack”
of “Filter 1 EG,” “Filter 2 EG,” “Amp 1 EG,” and “Amp 2
EG” (3–4a, 3–8, 4–3a, 4–6).
Decay:

Adjusts the decay times of the filter EG and amp

EG. This adjustment will be added to the “(Time) Decay”
of “Filter 1 EG,” “Filter 2 EG,” “Amp 1 EG,” and “Amp 2
EG” (3–4a, 3–8, 4–3a, 4–6).

Press the Done button to execute, and close the dialog
box.

Please be aware that the Compare function is not avail-
able for this command.

1–3: Velo. Zone

(Velocity Zone)

Here you can specify the velocity range at which each oscil-
lator will sound.
The “Velocity M.Sample” SW Lo

→

Hi” (1–2c) setting in con-

junction with these “OSC 1/2 Velocity Zone” settings will
determine the velocity ranges in which the High and Low
multisample or drum kit will sound.

1–3a: OSC 1/2 Velocity Zone

OSC1 Top