Korg TRITON Extreme, Manual

Page: 222 / 354

211
Ef
fect
1. In/Out
The I/Os of Master Effects MFX1 and MFX2 are mono-in/
stereo-out
. “Send1” and “Send2” determine the send level
to the Master Effects (
☞
“Routing” and “Mixer”). Stereo sig-
nals will be combined to a mono signal automatically and
sent to the effects.
The Master Effects do not output any Dry signals (signals
that are not processed by the effects). Therefore, they output
only Wet (signals that are processed by the effects) signals
(set via the “Wet/Dry” of the “MFX1” and “MFX2” pages).
The output signals from the Master Effects are routed to the
L/R bus with the output level specified by “Return1” and
“Return2.” These output signals are mixed with the output
signals from the bus specified by “BUS Select” (P8: “Rout-
ing” page in each mode) L/R, or with the output signals
from the bus specified by “BUS Select” (“Insert FX” page in
each mode) L/R, then routed to the Master EQ.
Selecting “000: No Effect” will mute the output. The pro-
cessed signal will be output in one of the following ways,
according to the type of effects 001–089.
The possible routing of effect signal inputs and outputs is
indicated in the upper left corner of the block diagram.
Pressing the ON/OFF button for MFX1 and 2 of the P9: Mas-
ter FX page in each mode will toggle between ON and OFF.
When OFF is selected, the output signals will be muted.
The TRITON Extreme can also turn MFX 1 and 2 off
separately from the setting of the ON/OFF button by
receiving MIDI control change message CC#94 and
CC#95 respectively. Value 0 will turn them off, and
value 1–127 will turn them on. You can also use “Effect
Global SW” (Global P0: 0–1b) to turn MFX1 and 2 on
and off. This MIDI control is performed on MIDI Global
Channel “MIDI Channel” (Global P1: 1–1a).
Double-size effects
You cannot select double-size effects for Master Effects
MFX1
and MFX2.
2. Routing
You can use up to two channels (MFX1 and 2) for the Master
Effects in any mode other than in Sampling mode. (You can-
not use the Master Effects in Sampling mode.) If you are not
using any Insert Effects in any mode, the Master Effects send
levels are determined by the “Send1 (MFX1)” and “Send2
(MFX2)” parameters specified independently for the oscilla-
tors (Program), timbres (Combination), tracks (Sequencer
and Song Play), and audio inputs (Global). For example
since you can adjust the master effect send levels for each
timbre/track, you can make settings so that reverb is
applied deeply to the piano, lightly to the strings, and not at
all to the bass. If you’re using insert effects, use the post-IFX
“Send 1” and “Send 2” to adjust the send amounts.
2–1. Program mode
Use the “Send1 (to MFX1)” and “Send2 (to MFX2)” parame-
ters of the P8: “Routing” page, or the “Send1” and “Send2”
parameters of the P8: “Insert FX” page for the post-IFX1–5
signals, to set the Master Effect send level.
If you have set “BUS Select” to L/R or Off, “Send1 (to
MFX1)
” and “Send2 (to MFX2)” of the “Routing” page are
effective. These parameters can be set for oscillators 1 and 2
individually.
If you have set “BUS Select” to IFX1–5, “Send1” and
“Send2” of the “Insert FX” page for the post-IFX1–5 signals
are effective. If you are using the Insert Effects in chain
(series), the “Send1” and “Send2” parameters for the post-
IFX (last IFX) are effective.
If you have set “BUS Select” to 1, 2, 3(Tube), 4(Tube), 1/2, or
3/4(Tube)
, the oscillator signals are output directly to
AUDIO OUTPUT (INDIVIDUAL) 1, 2, 3, or 4 (
☞
“Individual
Outputs”). In this case the Send 1 and Send 2 settings are
ignored, and the Master Effects will not be applied. (
☞
p.214)
Master Effects (MFX1, 2)
Stereo In - Stereo Out
Mono In - Mono Out
Mono In - Stereo Out
Effect
Effect
Effect
+
Effect +
Wet
+