Korg TRITON Extreme, Manual

Page: 125 / 354

114
Automatically-set parameters and their values
- : Not set automatically
Values enclosed in parentheses ( ) are automatically set
according to the settings you make in the dialog box.
*1
:Settings for analog and S/P DIF (“Input 1” and “Input 2”)
are made automatically.
*2
:The input source setting (“Input 1” and “Input 2”) you
specified for “Source Audio” in the dialog box will be set
automatically.
*3
:If “IFX” is Off this will be L/R. If IFX1...5 is selected this
will be IFX1...5.
*4
:If “Source Audio” is Mono-1 this will be L-Mono, if
Mono-2 this will be R-Mono, and if Stereo this will be
Stereo .
0–2: Input/Setup
Here you can select the input source for analog/digital
audio signals, and specify the input level, and bus. You can
also set-up for recording.
0–2a: Input (SAMPLING)
The settings you make here are valid only in Sampling
mode. These settings will also be valid when you move
from Sampling mode to Global mode.
External audio input settings for the TRITON Extreme
outside of Sampling mode are made in “Input (COMBI,
PROG, SEQ, S.PLAY, MEDIA)” (Global P0: 0–3a).
Input [Analog, S/P DIF]
Specifies the external audio source for input to the TRITON
Extreme.
Analog , S/P DIF each have their own independent set-
tings. After setting this “Input” parameter to select one
of these sources, make settings for the various Input1
and Input2 parameters. Multiple external audio input
sources can be input simultaneously.
Analog: The analog audio output from a device connected
to the AUDIO INPUT 1 and AUDIO INPUT 2 jacks can be
input to the TRITON Extreme.
S/P DIF:
The digital audio output from an instrument or
DAT etc. connected to the S/P DIF IN jack can be input to
the TRITON Extreme. The L channel of the S/P DIF input
will be input as specified by the Input1 setting below, and
the R channel as specified by the Input2 setting.
The S/P DIF input/output supports only the 48 kHz sample
rate.
If you want to sample via S/P DIF, you must set “Sys-
tem Clock
” (Global P0: 0–2a) to S/P DIF.
Input1:
Input2:
Level [0...127]
Specifies the level of the external audio signal that will be
input (selected by “Input” 0–2a). Normally you will set this
at 127.
The analog audio signals from the AUDIO INPUT 1, 2
jacks are converted by a AD converter from analog to
digital signals. This parameter sets the level of the sig-
nal immediately after it has been converted into digital
form. If the sound is distorted even though this level
setting is very low, it is possible that the sound is dis-
torting earlier than the AD converter. Try adjusting the
[LEVEL] knob or the output level of the external audio
source.
Parameter 1. Initialize
2. REC
Audio Input
3. Auto
Resample
through IFX
Input (Input Source): Analog, S/P DIF
*1
(Source Audio)
*2
Analog, S/P DIF
*1
Input1:
Level 127 127 127
Pan L000 L000 L000
BUS Select Off (IFX)*3 Off
Send1 000 000 000
Send2 000 000 000
Input2:
Level 127 127 127
Pan R127 R127 R127
BUS Select Off (IFX)
*3
Off
Send1 000 000 000
Send2 000 000 000
Recording Setup:
Source BUS L/R L/R L/R
Trigger Sampling START SW Sampling START SW Sampling START SW
Metronome Precount Off - -
Resample Manual Manual Auto
REC Sample Setup:
Save to RAM (Save to) RAM
Sample Mode L-Mono (Source Audio)
*4
Stereo
Sample Time: RAM Maximum - -
Sample Time: DISK 4min 59.999sec - -
Recording Level [dB] +0.0 +0.0 –12.0
REC Sample Preference:
Auto +12dB On Off Off On
BUS Select (P8 Routing):
BUS(IFX) Select L/R L/R (IFX)
0–1
0–2a
0–2c
0–2b