Parameter Guide
55
E: MIDI2 .............................................[P.Bend...CC#95]
Select the function that will be assigned to modulation
source MIDI 2 of the virtual patch. (With the factory settings,
this is CC#01.)
If the specified setting is assigned to another parameter,
an “*” will be shown in the right of the upper line of the
LCD screen.
F: MIDI Dump......................................... [1PROG...ALL]
Select the data that you wish to dump.
This function transmits the MS2000/MS2000R’s programs
and global settings to a MIDI data filer or computer con-
nected to the MIDI OUT connector. The same data can also
be transmitted to another MS2000/MS2000R.
For the dump procedure, refer to p.31 Basic Guide, Edit sec-
tion “4. Saving data on an external device (Data Dump).”
To receive this data, set Global mode Page 4D: MIDI FILTER
“SystemEx” to ENA, and you will be able to receive a data
dump at any time.
Data is transmitted and received on the global MIDI channel.
1PROG
Data for the currently selected program will be transmit-
ted.
PROG
Data for all programs will be transmitted.
GLOBAL
Global data will be transmitted.
ALL
All programs and global data will be transmitted.
The following times are required in order to perform the
various types of data dump.
A: ProgChg.................................................. [DIS, ENA]
Select whether or not program changes will be transmitted
and received.
ENA
Program changes will be transmitted and received.
DIS
Program changes will not be transmitted or received.
B: CtrlChg .................................................... [DIS, ENA]
Select whether or not MIDI control changes will be transmit-
ted and received.
ENA
MIDI control changes will be transmitted and received.
DIS
MIDI control changes will not be transmitted or received.
C: P.Bend ..................................................... [DIS, ENA]
Select whether or not pitch bend messages will be transmit-
ted and received.
ENA
Pitch bend messages will be transmitted and received.
DIS
Pitch bend messages will not be transmitted or received.
D: SystemEx ................................................ [DIS, ENA]
Select whether or not MIDI system exclusive messages will
be transmitted and received.
ENA
MIDI system exclusive messages will be transmitted and
received.
DIS
MIDI system exclusive messages will not be transmitted or
received.
E: NoteRcv..................................................[ALL...ODD]
When note data is received, specify the note numbers (even
numbered notes, odd numbered notes, all notes) that will be
sounded by the MS2000/MS2000R.
ALL
All note numbers will be received. Normally you will
leave this set at ALL. If you have connected an MS2000 or
an addition MS2000R to an MS2000R to increase the
polyphony, set one unit to EVN and the other to ODD so
that either one or the other will sound.
EVN
or ODD are valid only if the program has an
“Assign” setting (LCD Edit mode Page 03A: VOICE) of
Poly
.
There is no effect on the MIDI data that is received.
EVN
Even-numbered notes (C, D, E, F#, G#, A#) will be
sounded.
ODD
Odd-numbered notes (C#, D#, F, G, A, B) will be sounded.
F: P.Chg
Here you can freely specify the correspondence between the
MS2000/MS2000R
’s program numbers and the incoming
MIDI program change numbers.
External ..................................................... [000...127]
Select the incoming MIDI program change number.
Internal ..................................................... [A00...H16]
Select the MS2000/MS2000R program number.
Data to dump
Data size (Bytes)
Time required (seconds)
1PROG
291
Less than one second
PROG
37,157
approximately 15
GLOBAL
227
Less than one second
ALL
37,383
approximately 15
Page4: MIDI FILTER
ODD
EVN
MS2000R
MIDI OUT
MIDI IN
MS2000
EVN
MS2000R#1
MS2000R#2
MIDI OUT
MIDI IN
MIDI THRU
MIDI IN
MIDI keyboard, etc.
ODD
4F MIDI FILTER
P.Chg[000]:A01
External
Internal
Global parameters
Summary of Contents for MS2000
Page 1: ...2 E ...
