Parameter Guide
41
E: EG Reset .................................................. [ON, OFF]
Specify whether or not the EG will be reset for the second
and subsequent note-on.
If this is ON, the second note-on will start from a level of 0.
If this is OFF, the note will start from the current EG level.
“EG Reset” is valid in the following cases.
•When Page 03A: VOICE “Assign” is Poly.
•When Page 03A: VOICE “Assign” is Mono or Unison
and Page 03D: VOICE “Trigger” is Multi.
■
LFO (Low Frequency Oscillator)
These are the LFO (Low Frequency Oscillator) parameters
used to create cyclic change.
LFO1 is internally connected as the modulation source for
Page 05B: OSC1 “Control 1.”
LFO2 is internally connected as the modulation source for
oscillator pitch via the modulation wheel (on the MS2000R,
the modulation wheel of a connected external MIDI device).
If you have difficulty hearing the effect of the LFO,
increase the depth or intensity values of the modula-
tion destination.
A: Wave
❮
SELECT
❯
................................... [Saw...S/H]
Select the LFO waveform.
For LFO1 you can select from Saw, Squ, Tri, and S/H.
For LFO2 you can select from Saw, Squ (+), Sin, and S/H.
B: Key Sync ................................... [OFF, Timbre, Voice]
Specify how the LFO will be applied to a voice when note-on
occurs.
OFF
The LFO phase will not be reset when note-on occurs.
Timbre
The LFO phase will be reset at the first note-on that occurs
from a state of no keys pressed. Subsequently, modulation
will continue to be applied at the same LFO phase even for
subsequent note-on’s.
Voice
The LFO phase will be reset at each note-on, and modula-
tion of differing phases will apply to each voice.
C: Tempo Sync ..............................................[ON, OFF]
If this is ON, the LFO frequency will synchronize to the
tempo or to MIDI clock.
If the Global mode Page 3C: MIDI “Clock” setting is Inter-
nal
, the LFO will synchronize to the tempo specified by the
[TEMPO] knob. If the setting is External, the LFO will syn-
chronize to the MIDI clock received from an external MIDI
device.
If “Tempo Sync” is ON, setting Page 14A–17A:
PATCH1–4 “Destination” to LFO2Freq will have no
effect.
D: Frequency
❮
FREQUENCY
❯
..................... [000...127]
Specify the frequency of the LFO. Increasing this value will
result in a faster frequency.
This parameter will be displayed and can be set if “Tempo
Sync” is OFF.
If “Tempo Sync” is ON, this will indicate “Sync Note.”
E: Sync Note............................................. [1/32...1/1]
Specify the LFO frequency as a proportion of the tempo set
by the [TEMPO] knob. (
P.66 “How “Resolution” and “Sync
Note” values correspond to note values”)
This parameter will be displayed and can be set if “Tempo
Sync” is ON.
At a setting of 1/1, there will be one cycle every four beats.
At a setting of 1/2, there will be two cycles every four beats.
At a setting of 1/4, there will be one cycle every beat.
At a setting of 1/8, there will be two cycles every beat.
Page12: LFO 1
Page13: LFO 2
ON
OFF
Note on
Note on (Retrigger)
Note off
Tri
Sin
Saw
Squ
Squ (+)
S/H
Amplitude changes irregularly
(sample & hold)
Note on
Note on
Note on
Note all off
Note on
Note on
1VOICE
2VOICE
Program parameters
Summary of Contents for MS2000
Page 1: ...2 E ...
