35
C
OMBI
0
1
2
3
4
5
6
7
8
9
Select by Category
Selects a combination by category.
For the procedure, refer to “Select by Category” (
X50
microX
0–2: Prog
(Timbre Program)
Indicates the program that will be used by each timbre.
0–2a: Bank, Combi Select, Cat.Hold, 10’s
Hold,
(Tempo)
Bank
[Bank A…C]
Combi Select (Combination Select)
[0…127: name]
X50:
Cat. (Cat. HOLD)
X50:
10’s (10’s HOLD)
(Tempo)
[040...240, EXT]
In the same way as in the Combi page, select a combination
and set the tempo of the arpeggiator. (
☞
0–1a)
0–2b: Timbre Number & Category
Timbre Number & Category 1...8
This displays the timbre number and an abbreviated cate-
gory name.
0–2c: Program Select, Program Name
Program Select
[A000...g128]
Indicates the program that will be used by each timbre.
Choose this parameter, and use one of the following meth-
ods to select a program.
X50:
• Turn the [VALUE] dial.
• Use the [INC][DEC] buttons.
• Use numeric buttons [0]–[9] to enter the program
number, and press the [ENTER] button to confirm.
• Press the center of the ClickPoint to highlight the field in
the display, use [
π
][
†
] to make your choice, and press
the center to confirm.
• Use PROG BANK [A]–[GM] to select a bank (
• Receive a MIDI program change to select a program
microX:
• Turn the [VALUE] dial.
• Press the center of the ClickPoint to highlight the field in
the display, use [
π
][
†
] to make your choice, and press
the center to confirm.
• Use “Select by Category” to choose from the desired
category (
• Receive a MIDI program change to select a program
When you select a combination on this instrument, a
MIDI program change for the selected combination
number will be transmitted on the global MIDI channel
“MIDI Channel” (GLOBAL 1–1a). At the same time,
bank select, program change, and volume (CC#7) mes-
sages will be transmitted on the MIDI channel specified
for each timbre that is set to “Status” (2–1a) of EXT or
EX2
. However, these messages will not be transmitted
for timbres that are set to the same MIDI channel as the
global MIDI channel. In this case, EX2 timbres will
show the “Program Select” Bank as “–”, and will trans-
mit the bank number that was specified in “Bank (EX2)
MSB” and “Bank (EX2) LSB” (2–1a).
MIDI messages transmitted when you operate this
instrument are transmitted on the global MIDI channel.
At the same time, timbres whose “Status” is EXT or EX2
will transmit the same messages on their own MIDI
channel.
If bank select and program change messages are
received on a MIDI channel that matches the MIDI
channel of a timbre whose “Status” (2–1a) is INT, the
program of that timbre will change. However if the
MIDI channel of the incoming message matches the
global MIDI channel “MIDI Channel,” then the combi-
nation will change.
If you do not want the combination to change, you can
either change the global MIDI channel so that it does
not match the channel on which the program change
messages are being received, or you can uncheck
“Combi (Combi Change)” (GLOBAL 1–1b). Alternately,
you can uncheck “Bank (Bank Change)” (GLOBAL 1–
1b) so that only the program number will change and
the bank will remain the same.
If you wish to change a program without changing the
combination, you can also set “Program Change” (3–1a)
so that the program will change on certain timbres but
not on others.
This parameter can also be set from the 1: Ed–Tone Adjust,
Prog page.
Program Name
This displays part of the program name selected for the tim-
bre. In the case of the GM drums bank, drums bank (d) will
be indicated.
0–2a
0–2b
0–2c
0–2d