99
EFFECT
— Settings for drum Programs —
If a drum Program (“OSC Mode” Drums) is selected for tim-
bres in Combination mode and for tracks in Multi mode,
you can select “DKit” for “BUS Select.” If you select “DKit,”
the “BUS Select” (GLOBAL 4–3a) settings for each key
become effective, and each drum instrument sound will be
routed to the corresponding buses (e.g.: the snare sound is
sent to IFX, and other sounds to L/MONO and R).
If you select anything other than DKit, you may apply the
Insert Effect to all drum instruments, regardless of the
DrumKit settings.
If “BUS Select” is set to DKit, you will be able to select “DKit
IFX Patch.” This temporarily patches the “BUS Select” IFX
settings to send them to L/R.
For example, suppose you have assigned a drum program to
timbre 1 and a conventional program to timbre 2, and set
“BUS Select” to DKit for timbre 1 and to IFX for timbre 2.
Since timbre 1 is set to DKit, the “BUS Select” (GLOBAL 4–
3a) setting of the drum kit will be used.
If, for example, you have specified IFX for snare-type
sounds, use “DrumKit IFX Patch” when you do not want
the insert effect used by timbre 2 to be used for the drum
program. Select the Utility “DKit IFX Patch,” and tempo-
rarily send the drum kit IFX to L/R. Press the [MENU/OK]
button to execute, and the snare sounds will be sent to L/R.
When you want to return to the original sounds, select
IFX
→
IFX
.
DrumKit IFX Patch dialog box
After settings are made
3. Mixer
For each mode, use 8: Ed–InsertFX (or InsertFX) Setup page
parameters “Pan (CC#8),” “BUS Select,”“S1
(Send1(MFX1)),” and “S2 (Send2(MFX2))” to specify the
pan, bus select, and the send levels to master effects MFX1
and MFX2 for the signals that have passed through the
insert effect.
3–1. Pan (CC#8)
Specifies the pan after passing through the insert effect.
If the insert effect is a Stereo In–Stereo Out type (
☞
”In/
Out”), setting this parameter to C064 will allow the “Pan”
settings of the oscillator (PROG 6–1b, PROG 6–4), timbre
(COMBI 0–3a, 1–2a), track (MULTI 0–4/5a) to be used.
If the insert effect is a Mono In-Stereo Out or Mono In-
Mono Out
type (
☞
“In/Out”), the “Pan” of the oscillator,
timbre, or track will be ignored, and the sound will always
be panned to the center. In this case, the “Pan (CC#8)” (8–1)
that follows the insert effect will determine the final pan-
ning. L001 is far left and R127 is far right.
You can control these parameters via MIDI Control
Change CC#8.
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left
Center
Right
Post IFX Pan(CC#8)
C064
Left
Center
Right
L032
L000
R096
R127
Insert Effect = Stereo In - Stereo Out
Left
Center
Right
Left
Center
Right
OSC1
OSC2
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Post IFX Pan(CC#8)
C064
L032
L000
R096
R127
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left
Center
Right
Post IFX Pan(CC#8)
C064
Left
Center
Right
L032
L000
R096
R127
Insert Effect = Mono In - Stereo Out
OSC1
OSC2
Mono In - Mono Out