manualshive.com logo in svg

Korenix JetNet 7852G-4XG Series, User Manual

The Korenix JetNet 7852G-4XG Series switch offers high performance and reliability for industrial networks. Find the user manual for free download on our website for easy configuration and setup. Gain access to detailed instructions and troubleshooting tips to optimize performance. Download your manual at manualshive.com.

Share
Download
background image

Korenix Technology Co., Ltd.                                           

 

Industrial

 

Layer 3 Managed Ethernet Switch

 

 
 

_____________________________________________________________________________ 

Industrial Layer 3 Managed Ethernet SwitchUser Manual

 

 Page: 953/1568 

9.3.2 

Configuration Commands 

 

 
 
 

9.3.2.1    

ipv6 hop-limit 

 

This command defines the unicast hop count used in ipv6 packets originated by the node. The value is 
also included in router advertisements. Valid values for <hops> are 1-64 inclusive. The default 

“not 

configured

” means that a value of zero is sent in router advertisements and a value of 64 is sent in 

packets originated by the node. Note that this is not the same as configuring a value of 64. 

 

 

Syntax

 

 

ipv6 hop-limit <hops> 
no ipv6 hop-limit 

 

 

no 

– 

Use this command to disable the forwarding of IPv6 hop-limit. 

 

 

Default Setting

 

 

not configured 

Command Mode 

Global Config 

 

 
 
 
 

9.3.2.2    

ipv6 unicast-routing 

 

Use this command to enable the forwarding of IPv6 unicast packets. 

 

 

Syntax

 

 

ipv6 unicast-routing 
no ipv6 unicast-routing 

 

 

no 

– 

Use this command to disable the forwarding of IPv6 unicast packets. 

 

 

Default Setting

 

 

Disabled 

 

Command Mode

 

 

Global Config 

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Obihai OBi110 Quick Start Manual preview
OBi110
Brand: Obihai Pages: 2
ZyXEL Communications ZyXEL EES-1024AF User Manual preview
ZyXEL EES-1024AF
Brand: ZyXEL Communications Pages: 99
LaCie 301297U - 1TB Ethernet Disk XP Embedded Network Attached... Online Manual preview
301297U - 1TB Ethernet Disk XP Embedded Network Attached...
Brand: LaCie Pages: 67
City-Netek HomePNA PCI Adapter User Manual preview
HomePNA PCI Adapter
Brand: City-Netek Pages: 18
Planet ADE-3110 User Manual preview
ADE-3110
Brand: Planet Pages: 66
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93
Genexis FiberTwist XGS2410 Installation Manual preview
FiberTwist XGS2410
Brand: Genexis Pages: 7
IBM Redbooks Emulex VFA5 Product Manual preview
Redbooks Emulex VFA5
Brand: IBM Pages: 15
Baileigh 1019072 Operator'S Manual preview
1019072
Brand: Baileigh Pages: 20
JETWAY FDF13 Series Quick Installation Manual preview
FDF13 Series
Brand: JETWAY Pages: 15
IBEX Westermo Ibex-RT-330-5G Series Manual preview
Westermo Ibex-RT-330-5G Series
Brand: IBEX Pages: 36
Alcatel-Lucent 7950 Quality Of Service Manual preview
7950
Brand: Alcatel-Lucent Pages: 612
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2
ADTRAN OC-12 Manual preview
OC-12
Brand: ADTRAN Pages: 2
ADTRAN SFP Series Quick Start preview
SFP Series
Brand: ADTRAN Pages: 4
ADTRAN TRACER 4205 Quick Start Manual preview
TRACER 4205
Brand: ADTRAN Pages: 9
AT&T AC8200 Installation Manual preview
AC8200
Brand: AT&T Pages: 16
Cambium Networks PTP 820C User Manual preview
PTP 820C
Brand: Cambium Networks Pages: 672

Brands by name

Popular brands

Load more brands