Korenix JetNet 7852G-4XG Series User Manual Download Page 628

Page: 628 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 628/1568

6.25.2

Configuration Commands

6.25.2.1

auto-voip all

Use this command to enable VoIP Profile on the interfaces of the switch.

Syntax

auto-voip all
no auto-voip all

no -

Use this command to disable VoIP Profile on the interfaces of the switch.

Default Setting

Disable

Command Mode

Global Config.

6.25.2.2

auto-voip

Use this command to enable VoIP Profile on an interface or range of interfaces.

Syntax

auto-voip
no auto-voip

no -

Use this command to disable VoIP Profile on the interface.

Default Setting

Disable

Command Mode

Interface Config.

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands