Korenix JetNet 7852G-4XG Series User Manual Download Page 538

Page: 538 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 538/1568

6.18.2

Configuration Commands

6.18.2.1

ip dhcp snooping

This command enables the DHCP Snooping globally.

Syntax

ip dhcp snooping
no ip dhcp snooping

no -

This command disables the DHCP Snooping globally.

Default Setting

Disabled

Command Mode

Global Config

6.18.2.2

ip dhcp snooping vlan

This command enables the DHCP Snooping on a list of comma-separated VLAN ranges.

Syntax

ip dhcp snooping vlan <vlan-list>
no ip dhcp snooping vlan <vlan-list>

no -

This command disables the DHCP Snooping on VLANs.

Default Setting

Disabled

Command Mode

Global Config

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands