Korenix JetNet 7852G-4XG Series User Manual Download Page 45

Page: 45 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 45/1568

6.1.3

show process cpu

This command provides the percentage utilization of the CPU by different tasks.

Syntax

show process cpu

It is not necessarily the traffic to the CPU, but different tasks that keep the CPU busy

Default Setting

None

Command Mode

Privileged Exec

Display Message

The following shows example CLI display output for the command.

Memory Utilization Report

status

bytes

------ ----------

free

250978304

alloc

275599360

CPU Utilization:

PID

Name

5 Secs

60 Secs

300 Secs

-----------------------------------------------------------------

1030

osapiTimer

0.00%

0.02%

1032

_interrupt_thread

0.00%

0.02%

1034

bcmL2X.0

1.99%

2.10%

1.81%

1035

bcmCNTR.0

1.59%

1.42%

1.19%

1038

bcmLINK.0

2.99%

2.84%

2.44%

1040

bcmL2X.1

1.99%

2.09%

1.81%

1041

bcmCNTR.1

1.39%

1.40%

1.19%

1042

bcmLINK.1

2.99%

2.87%

2.45%

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands