Korenix JetNet 7852G-4XG Series User Manual Download Page 1219 | Manualshive

Page: 1219 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1219/1568

11.3.20

Managing MLD Snooping

11.3.20.1

Configuring MLD Snooping Global Configuration and Status Page

Use this menu to configure the parameters for MLD Snooping, which is used to build forwarding lists for
multicast traffic. Note that only a user with Read/Write access privileges may change the data on this
screen.

Selection Criteria

Admin Mode

- Select the administrative mode for MLD Snooping for the switch from the pulldown

menu. The default is disable.

Non-Configurable Data

Multicast Control Frame Count

- The number of multicast control frames that are processed by the

CPU.

Interfaces Enabled for MLD Snooping

- A list of all the interfaces currently enabled for MLD

Snooping.

Data Frames Forwarded by the CPU

- The number of data frames forwarded by the CPU.

VLAN Ids Enabled For MLD Snooping

- Displays VLAN Ids enabled for MLD snooping.

Command Buttons

Submit

- Update the switch with the values you entered. If you want the switch to retain the new

values across a power cycle you must perform a save. You will only see this button if you have
Read/Write access privileges.

«
...
1217
1218
1219
1220
1221
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: D-Link Pages: 100

Brand: D-Link Pages: 134

Brand: D-Link Pages: 187

Brand: D-Link Pages: 225

Brand: D-Link Pages: 31

Brand: D-Link Pages: 35

DES-1016D - Switch

Brand: D-Link Pages: 19

Brand: D-Link Pages: 107

AirPlusXtremeG DI-624

Brand: D-Link Pages: 5

Brand: D-Link Pages: 48

Brand: Cambium Networks Pages: 29

Brand: Observint Pages: 11

Brand: Falcon Pages: 24

Brand: Google Pages: 14

BladeCenter Management Module

Brand: IBM Pages: 184

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: Buffalo Pages: 2

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands