Korenix JetNet 7852G-4XG Series User Manual Download Page 1074 | Manualshive

Page: 1074 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1074/1568

11.2.6

Viewing Logs

11.2.6.1 Viewing Buffered Log Configuration
Page

This log stores messages in memory based upon the settings for message component and severity. On
stackable systems, this log exists only on the top of stack platform. Other platforms in the stack forward
their messages to the top of stack log.

Selection Criteria

Admin Status

- A log that is "Disabled" shall not log messages. A log that is "Enabled" shall log

messages. Enable or Disable logging by selecting the corresponding line on the pulldown entry field.

Behavior

- Indicates the behavior of the log when it is full. It can either wrap around or stop when the

log space is filled.

Command Buttons

Submit

- Update the switch with the values you entered.

«
...
1072
1073
1074
1075
1076
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Brand: Vaisala Pages: 32

Brand: B&B Electronics Pages: 2

Brand: SurfControl Pages: 2

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

SmartSTACK ELS100-24TXM

Brand: Cabletron Systems Pages: 117

JetFusion 2100 Series

Brand: Paradyne Pages: 296

Brand: ADTRAN Pages: 20

Brand: UNICORECOMM Pages: 19

Brand: NetComm Pages: 65

Brand: EINHELL Pages: 32

Brand: IBM Pages: 75

Brand: Lobaro Pages: 26

Brand: D-Link Pages: 2

PMP 450d Series

Brand: Cambium Networks Pages: 215

Brand: Tripp Lite Pages: 3

Brand: 3Com Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands