Korenix JetNet 7852G-4XG Series User Manual Download Page 1022

Page: 1022 / 1568

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 1022/1568

10.2

Configuration Commands

10.2.1

OpenFlow Instance

This command enters OpenFlow instance.

Syntax

openflow instance <instance-id>

Default Setting

None

Command Mode

Global Config

10.2.2

OpenFlow Enable/Disable

To configure admin mode of OpenFlow instance.

Syntax

enable
no enable

Default Setting

Disable

Command Mode

OpenFlow Instance Mode

«
...
1020
1021
1022
1023
1024
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands

Korenix JetNet 7852G-4XG Series, User Manual

Search results

Summary of Contents for JetNet 7852G-4XG Series

Reviews:

Related manuals for JetNet 7852G-4XG Series

Brands by name

Popular brands