JetNet 7014G Industrial 10 GbE plus 4 GbE SFP Ethernet Switch
Quick Installation Guide V1.0
The JetNet 7014G is an pure Gigabit Managed Switch with 10 ports Gigabit Ethernet plus , and
4 Gigabit SFP for optical fiber connection It adopts high efficiency Ethernet MAC controller
with 40Gbps Switch fabric bandwidth, 9K jumbo frame forwarding and powerful Layer-3 IP
routing capability. The robust system design makes the JetNet 7014G survive under harsh
outdoor environment with extreme electric magnetic interference and the variation of
environment temperature. The hardware switching basis Layer-3 Routing features enabled the
IP based packet forwarding with high performance, low latency and security. It provides your
network infrastructure with great performance and safety with network access control, and
handle burst packet with smart buffer management for IP surveillance in real infrastructure.
Package Check List
JetNet 7014G
DIN Mounting kit
DB-9 to RJ-45 RS-232 Console Cable
Quick Installation Guide
Wiring the Power Inputs & Earth Grounding
1. Insert the positive and negative wires into the V+ and V- contact on the
terminal block connector.
2. Connect the Chassis
Grounding to Earth Ground
system to obtain electromagnetic
immunity to resist lighting,
electro static discharge and
electric fast transient.
3. Tighten the wire-clamp screws to prevent the power wires from being loosened.
Notes:
The recommended working voltage is DC 24V. Use the UL Listed LPS Power supply
with output Rating 9~36 VDC, minimum 2A currents.
Installation
You can configure JetNet 7014G via the RS-232 console with the attached console cable. Or
you can remotely manage the switch via network. You can choose Telnet/SSH,
Web/HTTPS management.
Preparation for console management
Attach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45 connector to
the console port of the JetNet Switch.
1. Go to Start ► Program ► Accessories ► Communication ► Hyper Terminal
2. Give a name to the new console connection.
3. Choose the COM name and select the correct serial settings. The serial port settings are as
below: Baud Rate:115200/Parity: None/Data Bit: 8/Stop Bit: 1
4. After connected, you will see the Switch login request. Type the username and password
and then you can login. The default username is “admin”, password is “admin”.
5. Follow the manual to configure the software features.
Preparation for Web management
1. Launch the web browser on the PC.
2. Type http://JetNet Managed Switch_IP_Address (The default IP address is 192.168.10.1.),
then press Enter.
3. The login screen will appear next. Type in the user name and password and click “OK”
button. The default user name and password is admin/admin.
4. At the left column of the web management interface are the software features, where ring
column will list the available settings.
5 Years Warranty
Each of Korenix’s product is designed, produced, and tested with high industrial standard.
Korenix warrants that the product(s) shall be free from defects in materials and
workmanship for a period of five (5) years from the date of delivery provided that the
product was properly installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the
European Parliament and of the Council of 27 January 2003 on the restriction of the use of
certain hazardous substances in electrical and electronics equipment (RoHS Directives &
RoHS 2.0)
Korenix Customer Service
KorenixCARE is Korenix Technology’s global service center, where our professional staffs
are ready to answer your questions at any time.
Email address of Korenix Global Service Center : [email protected]
Support
Device Management
Mounting the unit
The DIN Rail clip on the rear of JetNet 7014G, and supports 35mm DIN rail.
Interface Introduction
JetNet 7014G supports 10 ports Gigabit Ethernet RJ-45, and 4 ports swappable Gigabit
Ethernet SFP socket for fiber connection.
Wiring the Digital Input
The Digital Input (DI) contacts are in
the bottom. It accepts one external DC
type signal input and can be configured
to send alert message through Ethernet
when the signal is changed. The signal
may trigger and generated by external
power switch, like as door open trigger
switch for control cabinet.
Note:
The DI accepts DC type signal and supports isolated input circuit with Digital High
Level input DC 11V~30V and Digital Low Level input DC 0V~10V. Do not apply voltage
higher than the specification; it may cause internal circuit damage or a wrong action of DI.
Connecting the Surge/Lighting protection
The surge protection activate screw located on the rear side that nearby the DIN rail clip.
Always tighten the screw and ensure the surge protection activate
screw is tighten with Earth-Ground well.
Note:
1. Ensure the Surge/Lighting is well connecting with
Chassis Grounding.
2. Remove the Surge/Lighting Screw before perform insulation/
Hi-pot testing.
3. Never install or work on/with the equipment or the cabling
during the period of its lightning activity.
Wiring the Relay Output
The relay output contacts are in the bottom
side. The relay output (DO) is controlled by
the pre-defined operating rules.
To activate relay output function, please
refer to the User’s Manual for more relay
output management information.
Notes:
The relay contact only supports
0.5 A current, DC 24V. It is not recommended to apply voltage and current higher than the
specifications.
4
3
1
2
9
10
5
6
11
12
7
8
13
14
10 GbE/TX, 4 100/1000 SFP
Managed Gigabit Switch
Reset
SYS
R.S.
1
DI
2
PWR
CONSOLE
115200.N.8.1
DO
Surge Protect Enable
Surge Protect Enable