JetNet 5310G Industrial 8 PoE + 2G Managed High Power PoE Switch
JetNet 5810G Industrial 8FE + 2G Combo Switch with DC12~24V to 48VDC
Power Booster
Quick Installation Guide V3.0
Korenix JetNet 5310G/JetNet5810G is a DIN Rail type industrial Gigabit managed Power
over Ethernet Switch, which designed with eight 10/100TX PoE injector ports and two Gigabit
RJ-45 / SFP combo ports for highly critical PoE applications such as real time IP video
surveillance, WiMAX systems and Wireless APs. All of the 8 ports of the switch are compliant
with both IEEE 802.3af PoE and IEEE 802.3at high power PoE standards and can deliver up
to 15.4W and 30W power per port to enable the high-power requiring devices, such as Wireless
APs, PTZ and dome network cameras, etc.
Package Check List
JetNet 5310G/JetNet5810G with DIN Rail clip
Console Cable (RJ-45/DB9)
Quick Installation Guide
Installation
5 Years Warranty
Each of Korenix’s product is designed, produced, and tested with high industrial standard.
Korenix warrants that the product(s) shall be free from defects in materials and workmanship
for a period of five (5) years from the date of delivery provided that the product was properly
installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted product are
caused by damage resulting from force measure (such as floods, fire, etc.), other external
forces such as power disturbances, over spec power input, or incorrect cabling; or the
warranted product is misused, abused, or operated, altered and repaired in an unauthorized
or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment (RoHS Directives & RoHS 2.0)
Korenix Customer Service
KorenixCARE is Korenix Technology’s global service center, where our professional staffs
are ready to answer your questions at any time.
Email address of Korenix Global Service Center : [email protected]
Support
You can configure JetNet 5310G/JetNet5810G via the RS-232 console with the attached
console cable. Or you can remotely manage the switch via network. You can choose
Telnet/SSH, Web/HTTPS management.
Preparation for console management
Attach the RS-232 DB9 connector to your PC’s COM port. Connect the RJ-45 connector to
the console port of the JetNet Switch.
1. Go to Start ► Program ► Accessories ► Communication ► Hyper Terminal
2. Give a name to the new console connection.
3. Choose the COM name and select the correct serial settings. The serial port settings are as
below: Baud Rate:9600/Parity: None/Data Bit: 8/Stop Bit: 1
4. After connected, you will see the Switch login request. Type the username and password
and then you can login. The default username is “admin”, password is “admin”.
5. Follow the manual to configure the software features.
Preparation for Web management
1. Launch the web browser on the PC.
2. Type http://JetNet Managed Switch_IP_Address (The default IP address is 192.168.10.1.),
then press Enter.
3. The login screen will appear. Type in the user name and password and click “OK” button.
The default user name and password is admin/admin.
4. At the left column of the web management interface are the software features, where ring
column will list the available settings.
Device Management
Mounting the unit
Mount the din-rail clip on the rear of JetNet 5310G/5810G on the DIN rail.
Interface Introduction
JetNet 5310G/5810G includes 10/100Mbps Fast Ethernet ports, SFP slot, RS232 console port,
Reset button and LEDs for system and port indication.
Dimension:
JetNet 5310G :95 x 160 x 136.2mm (W x H x D), with DIN Rail Clip
JetNet 5810G :95 x 160 x 141.5mm (W x H x D), with DIN Rail Clip
Note:
The DI accepts DC type signal and supports isolated input circuit with Digital High
Level input DC 11V~30V and Digital Low Level input DC 0V~10V.
Do not apply voltage higher than the specification; it may cause internal circuit damage or a
wrong action of DI.
Connecting the Surge / Lighting protection
The surge protection activate screw located on
the rear side under the DIN rail.
Always tighten the screw and ensure
the Chassis-Grounding screw is
connected with Earth-Ground well.
Note: 1. Ensure the Surge/Lighting is
well connecting with Chassis Grounding.
2. Remove the Surge/Lighting Screw before
perform insulation/Hi-pot testing.
3. Never install or work on/with the equipment
or the cabling during the period of its lightning activity.
Wiring the Relay Output
The relay output contacts are
in the bottom side. The relay
output (DO) is controlled by
the pre-defined operating
rules. To activate relay output
function, please refer to the
User’s Manual for more relay output management information.
Notes:
The relay contact only supports 0.5A current, DC 24V. It is not recommended to
apply voltage and current higher than the specifications.
Wiring the Digital Input
The Digital Input (DI) contacts are in
the bottom of the device. It accepts one
external DC type signal input and can
be configured to send alert message
through Ethernet when the signal is
changed.
Power Input Range
Wiring the Power Inputs & Earth Grounding
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Connect the Chassis Grounding
to Earth Ground system to obtain
electromagnetic immunity to resist
lighting, electro static discharge and
electric fast transient.
3. Tighten the wire-clamp
screws to prevent the power
wires from being loosened.
Power Input
2x DC 48V (48-75V)
2x DC 24V (10-60V)
Remark
PoE Switch
w/PoE Power Booster
JetNet 5310G
JetNet 5810G
