JetCon 3701G
Quick Installation Guide v1.0
This is warranty is voided if defects, malfunc
tion
s or failures o
ft
he
warranted Product are caused by damage re
sultin
g from force measure
(such as
flood
s,
fi
re, etc.), other external forces such as power
disturbances, over spec power input, or incorrect cabling; or the
warranted produc
ti
s misused, a
bused, or operated, altered and
repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT
plug in power connector when power is on.
The produc
ti
s in compliance with Direc
tiv
e 2002/95/EC and 2011/65/EU
o
ft
he European Parliament and o
ft
he Council of 27 January 2003 on the
rest
rictio
n o
ft
he use of certain hazardous substances in electrical and
electronics equipment (RoHS Dire
cti
ves & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our
professional sta
ff
are ready to solve your problems at any
tim
e Korenix
global service center's e -mail is [email protected].
For more inform
atio
n and documents download please visit our website:
http://www.korenix.com/downl
oads.htm
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with
high industrial standard. Korenix warrants tha
tt
he Product(s) shall be
free from defects in materials and workmanship for a period o
ffiv
e (5)
years from the date of delivery provided tha
tth
e Product was properly
installed and used.
Support
DIP Switch Setting
Note:
A
ft
er adjus
ti
ng the DIP-switch, please reboot the unit to ac
ti
vate the
new se
tti
ngs.
Dipswitch
Func
ti
onality
Switch 1
On: Enable power event alarm
O
ff
: Disable.
Switch #2
On: SFP speed at 100Mbps
O
ff
: SFP speed at 1000Mbps
Switch #3
On: Enable LLF func
ti
on
O
ff
: Disable.
Wiring the Relay Output
The relay output contacts are in the middle of the terminal block connector
as shown below. By inser
ti
ng the wires and se
tti
ngs the DIP switch of the
respec
ti
ve alarm func
ti
on to “ON”, relay output alarm will detect port or
power fault, and form a short circuit. The alarm relay output is “Normal
Open”. For more informa
ti
on, please refer Manual chapter for more detail.
Note:
The relay contact only support 1A current, DC 24V. It does not recommend
apply higher voltage and current that over this speci
fi
ca
ti
on.
Wiring the Power Inputs
1. Insert the posi
ti
ve and nega
ti
ve wires into the V+ and V- contact on the
terminal block connector.
2. Tighten the wire-clamp screws to prevent the power wires loosened.
Copyright
Copyright © 2014 all rights reserved. No part of this publica
ti
on may be
reproduced, adapted, stored in a retrieval system, translated into any
language, or transmi
tt
ed in any form or by any means without the wri
tt
en
permission of the supplier.
About the Quick Installation Guide
This Quick Installa
ti
on Guide is intended to guide professional installer to
install and con
fi
gure the JetCon 3701G. It covers procedures to assist you
in avoiding unforeseen problems.
Introduction
JetCon 3701G is an Ethernet to
fi
ber op
ti
c media converter. It conforms
IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, and IEEE 802.3ab 1000Base-T
supports RJ-45 copper to Gigabit
fi
ber conversion. JetCon3701G are
classi
fi
ed as power source equipment (PSE), providing 15.4/30 wa
tt
s to
powered devices(PD). It could be used to power IEEE 802.3af/at compliant
powered devices (PD). The JetCon 3701G adopts rugged metal case design
to operate in harsh environment (-40~75
°
C). It also IP-31 standard
protec
ti
on. It features link loss forwarding raise an alarm when a remote
fault occurs and also adopts one relay output to alarm users if a port link or
power fails. Alarm can be enable/disable by dip switch. The
fi
ber port
supports SFP sockets for several of SFP transceiver to achieve di
ff
erent link
distance.
JetCon 3701G recommend working voltage is DC 48V. (Input range: DC10~
60 V)
Package Check List
JetCon 3701G Industrial Media Converter
Quick Installa
ti
on Guide
Installation
Attention:
This is a Class 1 Laser/LED product.
Don’t stare into the Laser/LED
Beam.
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 3701G V2 on
the DIN rail. For informa
ti
on about the DIN Rail installa
ti
on, please refer
to user’s manual.
Grounding JetCon 3701G
There is one grounding screw on the
bo
tt
om side of JetCon 3701G . Connect the
frame grounding of JetCon 3701G to the
grounding surface to ensure safety and
prevent noise for communica
ti
on interference.
Connecting to Network
1.
Connecting the Gigabit PoE port: The port supports IEEE 802.3at PoE
standard, and o
ff
er 2 event PoE behavior. Thus, the PoE port can
o
ff
er 15W/30W power, and system o
ff
er 60W with DC12V input
under 70C one end of an Ethernet cable into the UTP port of JetCon
3701G , while the other end is connected to the a
tt
ached networking
device. UTP port support auto MDI/MDIX func
ti
on. The LNK / ACT
LED will turn on and
fl
ash to indicate RJ-45 port link and the packets
received and transmi
tt
ed from RJ-45.
2.
Install Gigabit SFP transceiver and make the connection: Connect
the
fi
ber port on your JetCon 3701G to another Gigabit Fiber
Ethernet device, by following the
fi
gures below. Wrong connec
ti
on
will cause the
fi
ber port not working properly.
The SFP Fiber port supports 2 LEDs for link/ac
ti
vity and full duplex/
collision, once the gigabit
fi
ber port is in up, the link LED will be
trigger to”ON”
