manualshive.com logo in svg

Kontron coolMONSTER/C3, User Manual

Share
Download
Kontron coolMONSTER/C3 User Manual Download Page 74

KONTRON

 Appendix B: BIOS Operation

68

CMP/P3 and CMP/C3 User’s Guide

26.7 

Boot Menu

Feature

Option

Description

Floppy Check

Disabled

Enabled

Enabled verifies floppy type on boot; disabled speeds

boot.

Summary Screen

Disabled

Enabled

If enabled, a summary screen is displayed just before

booting the OS to let the user see the system

configuration.

QuickBoot Mode

Disabled

Enabled

Allows the system to skip certain tests while booting.

This will decrease the time needed to boot the system.

Dark Boot 

Disabled

Enabled

If enabled, system comes up with a blank screen

instead of the diagnostic screen during bootup.

8

Boot Device Priority

Submenu

Opens boot device priority submenu.

Onboard LAN RPL ROM

Disabled

Enabled

Enables RPL ROM of the onboard LAN controller.

Supports Intel PXE. 

Check the Intel Web site for more information.

Notes

: In the Option column, bold represents default settings.

(*) A CMOS battery backup must be present for this selection to work properly.

26.7.1. 

Dark Boot

After you turn on or reset the computer, Dark Boot displays a graphical logo (default is a blank
screen) instead of the text based POST screen, which displays a number of PC diagnostic messages.

The graphical logo stays up until just before the OS loads unless:

!

 

You press <Esc> to display the POST screen

!

 

You press <F2> to enter Setup

!

 

POST issues an error message

!

 

The BIOS or an option ROM requests keyboard input

Summary of Contents for coolMONSTER/C3



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands