Kontron AT8902M User Manual Download Page 71

Page: 71 / 92

AT8902M

Software Description

Page 4 - 6

AT8902M User Guide

• RFC 1723 - RIP v2

• RFC 1765 - OSPF Database Overflow

• RFC 1812 - Requirements for IP Version 4 Routers

• RFC 2328 - OSPF v2 w/ Equal Cost Multipath support

• RFC 3046 - DHCP/BootP Relay

• RFC 3101 - OSPF with NSSA support

• RFC 3768 - Virtual Router Redundancy Protocol (VRRP)

• Route Redistribution across RIP and OSPF

• VLAN Routing

4.1.4

QoS

• Bandwidth Policing (Min and Max; per port/per VLAN)

• Committed Information Rate (CIR)

• Maximum Burst Rate (MBR)

• Per Port (Interface)

• Per VLAN

• Filtering (L3/L4 Access Lists)

• IP Classification - 6 Tuple Classification

• RFC 2474 - DiffServ Definition

• RFC 2475 - DiffServ Architecture

• RFC 2597 - Assured Forwarding PHB

• RFC 3246 - An Expedited Forwarding PHB

• RFC 3260 - New Terminology and Clarifications for DiffServ

4.2

Supported MIBs

The Software supports the following MIBs.

4.2.1

Enterprise MIB

• Support for all managed objects not contained in standards based MIBs.

Summary of Contents for AT8902M





























































































Search results

Summary of Contents for AT8902M

Reviews:

Brands by name

Popular brands

Kontron AT8902M, User Manual

Search results

Summary of Contents for AT8902M

Reviews:

Brands by name

Popular brands