102
5.3 Exposure with DR Detector (Aero Sync mode)
•
The selected Exam. Tag is added to the Exam.
Tags display area . By repeating from step 1,
Exam. Tags can be added.
4
When finished selecting/adding the Exam.
Tags, press [Perform] .
•
The exposure screen is displayed.
HINT
•••••••••••••••••••••••••••••••••••••
•
When only reserving an examination, after adding the
Exam. Tag, press [Schedule]. After reservation is per
-
formed, the initial screen is displayed .
•
Returning to the initial screen by pressing [Schedule]
does not set study date and time of image supplemen-
tal information automatically .
•
It is also possible to register multiple exposure methods
in 1 Exam. Tag. Register these methods when install
-
ing .
•
If you have set to register the Exam. Tags automati
-
cally, the body part selection screen is not displayed .
The display transitions to the exposure screen.
•••••••••••••••••••••••••••••••••••••••••••••••••••••
5 .3 .5 Exposure
The exposure procedure in Aero Sync mode is as fol
-
lows .
Prepare for exposure using Aero Sync mode accord
-
ing to the following procedure . The procedure varies
depending on the setting of the [AeroSync Button] on
the system monitor screen .
IMPORTANT
•••••••••••••••••••••••••••••••••••••
•
Always check the patient information and exposure
conditions before exposure.
• Available X-ray detection level varies depending on
the DR Detector model .
• In the event of a communication error and depending
on the timing at which the error has occurred, images
may not be displayed and the DR Detector may not
contain any images that have not been transferred
(the same status as that observed when no exposures
have been carried out) . If this is the case, suspend the
study and display the exposure screen from the list
screen . This operation may successfully recover the
images .
•••••••••••••••••••••••••••••••••••••••••••••••••••••
HINT
•••••••••••••••••••••••••••••••••••••
•
The procedure is explained with the use of the Aero
-
DR 3 1417HD as an example.
•••••••••••••••••••••••••••••••••••••••••••••••••••••
z
When the [AeroSync Button] is OFF
1
Prepare the DR Detector.
•
When the DR Detector is ready to start expo
-
sure, "Ready" is displayed .
• A message "Ready" is displayed in the mes-
sage/button area, then the screen is locked .
• To change the X-ray detection level, press
[Pause] to enable modification. After changing
the detection level, press [Restart], then the
message "Ready" is displayed .
Summary of Contents for CS-7
