Kongsberg Simrad MF90 Page 62 Installation Manual Download | Manualshive

Page: 62 / 426

background image

60

476671/B

Compass safe distance

•

Model

: MF90 Processor Unit (HT20470)

•

Standard compass

: 150 cm

•

Steering compass

: 130 cm

Related topics

Preparations, page 42
Location of hardware units on the bridge, page 56
Installing the MF90 system hardware units, page 126
Drawing file, page 364

Choosing the best location for the Operating Panel

The Operating Panel offers all necessary control functions for normal operation. The
Operating Panel must be mounted in a nearly horizontal position, and within easy viewing
range of the display.

We recommend that the Operating Panel is positioned in the same physical direction as the
display, so that "up" on the operating panel is the same as "up" on the display. Experience
has shown that this will make it easier to use the trackball on the operating panel when you
wish to control the cursor on the display.

Observe the limitations due to the cable lengths.

The length of the Ethernet cable provided with the Mk2 Operating Panel is five -5- metres.
If necessary you can replace this cable with a longer Ethernet cable. A replacement cable
must be purchased locally.

The length of the USB cable provided with the Mk3 Operating Panel is three -3- metres.

Compass safe distance (Mk2)

•

Make and model

: MF90 Operating Panel Mk2

•

Standard compass

: 25 cm

•

Other compass

: 16.5 cm

Compass safe distance (Mk3)

•

Make and model

: MF90 Operating Panel (Mk3)

•

Standard compass

: This information is currently not available.

•

Other compass

: This information is currently not available.

Simrad MF90 Installation Manual

«
...
60
61
62
63
64
...
»

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Simrad MF90

Brand: Raymarine Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands