manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 302

300

476671/B

The MF90 system can be provided with one of the following hull units:

Hull Unit

Lowering depth (m)

Transducer cables

(m)

Maximum speed

(knots)

4.6

MF90

1.0

10

20

4.6

MF94

2.1

7

19

Note

We strongly recommend that you do not specify a higher speed than the hull
unit is designed for.

If the speed limit is exceeded a message is issued by the MF90 system.

Screen Recording

We recommend that you do not make any changes to these settings.

Recording

We recommend that you do not make any changes to these settings.

5

At the bottom of the page, select

Apply

to save your settings.

6

Continue your work in the

Installation

dialog box, or select

OK

to close it.

Related topics

Configuring the MF90 system for normal operation, page 297

Configuring the MF90 system for data recording

Record

allows you to record echo data. The data are saved on the hard disk, or on an external

data storage device, according to the preferences you have defined. If necessary the files can
be copied or moved to another storage device or a network drive.

Prerequisites

If you wish to save your recorded data on an external hard disk, make sure that it is
connected to the computer.

Simrad MF90 Installation Manual

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands