manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 300

298

476671/B

4

Adjust the settings to fit your requirements.

5

At the bottom of the page, select

Apply

to save your settings.

6

Continue your work in the

Installation

dialog box, or select

OK

to close it.

Related topics

Configuring the MF90 system for normal operation, page 297

Setting up the alarm limits for system protection

Safe operation of the MF90 system is made possible using multiple sensors that monitor
the operation and the performance. Whenever a suspicious event takes place, a relevant
message, warning or alarm is provided. Selected alarm limits may be adjusted to fit your
operational requirements.

Context

The

System Protection

page allows you to specify alarm limits for the hull unit and the

transducer. Additional system protection features are also listed. These function are
automatically monitored by the software in the MF90 system. You are not permitted to
change the alarm limits.

If an alarm limit is exceeded a relevant message is issued by the MF90 system. At the same
time, the relevant descriptive text is provided with a dark background.

Procedure

1

Open the

Setup

menu.

2

On the

Setup

menu, select

Installation

.

Observe that the

Installation

dialog box opens. This dialog box contains a number of

pages selected from the menu on the left side.

3

On the left side of the

Installation

dialog box, select

System Protection

to open the page.

Simrad MF90 Installation Manual

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands