manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 175

476671/B

173

RJ45 High speed Ethernet cable (From computer to transceiver)

A high capacity Ethernet cable connects the computer to the transceiver. An extra Ethernet
cable can be installed for redundancy purposes. The cables can be ordered from Kongsberg
Maritime, or provided by the installation shipyard.

A

Local Ethernet connection

B

Connection on external network
device

We strongly recommend that you install
minimum two Ethernet cables between
the sonar room and the bridge. One
cable is for operational use, while the
other is spare.

The maximum length of the Ethernet cable is 100 meters.

Each end of the Ethernet cable must be terminated with a Phoenix Contact "Variosub RJ45
Quickcon" connector. Connectors and mounting instructions for are provided in the sonar
delivery.

Minimum cable requirements

It is very important that a high-quality Ethernet cable is
used. You must use Cat 5e STP (Shielded Twisted Pair)
quality or better. Using cables with lower bandwidth
capacity will reduce performance.

Cable layout and interconnections

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands