manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 159

476671/B

157

8

Optional: Connect the Ethernet cable from the Processor Unit to the local area network
(LAN).

9

Optional: Connect the signal cable from the Processor Unit to the synchronization
system.

Related topics

Cable layout and interconnections, page 143
Cable plans, page 145
Installing the MF90 cables, page 154
Cable drawings and specifications, page 164

Installing the sonar room cables

The sonar room cables include those used to connect the MF90 units to AC mains power, as
well as the control cables between the units. A high capacity Ethernet cable connects the
topside computer to the transceiver.

Procedure

1

Connect the power cables, but do not apply AC mains to any of the system units.

a

Connect the power cable from the uninterruptible power supply (UPS) to the
AC power outlet.

b

Connect the power cable from the Transceiver Unit to the power outlet on the
uninterruptible power supply (UPS).

c

Connect the power cable from the internal fans or heat exchanger to the power
outlet on the uninterruptible power supply (UPS).

2

Connect the ground cables.

a

Connect the ground cable from the Transceiver Unit to vessel ground.

b

Connect the ground cable from the hull unit mounting flange to vessel ground.

3

Connect the Ethernet cable from the Processor Unit to the Transceiver Unit.

4

Connect the power cable from the Motor Control Unit to the AC power outlet.

5

Prepare the installation of the transducer cable.

The transducer cable is connected to the Transceiver Unit using a large custom plug.

a

Make sure that the transducer cable is long enough to allow the transducer to
be lowered and hoisted without causing any damage to the cable, the hull unit,
or other equipment in the sonar room.

Cable layout and interconnections

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands