Kongsberg M3 Sonar Reference Manual Download

Page: 86 / 182

922-20297001/1.2

Description

•

Ethernet Test - 100Mbps

You can test your 100-Mbps link to make sure that the
link throughput is available. The test uses 95 percent
utilization.

•

Ethernet Test - 10Mbps

You can test your 10-Mbps link to make sure that the
link throughput is available. The test uses 95 percent
utilization.

•

Imaging 10

You can use this sonar application for navigation and obstacle avoidance. This application
uses a 10-degree Tx vertical beamwidth.

•

Imaging 20

You can use this sonar application for navigation and obstacle avoidance. This application
uses a 20-degree Tx vertical beamwidth.

•

Imaging 40

You can use this sonar application for navigation and obstacle avoidance. This application
uses a 40-degree Tx vertical beamwidth.

•

Rub Test

Use this sonar application as part of a system test to make sure that the transducer is
receiving a signal. Rub the transducer and make sure that bright streaks or rings appear
in the sonar view.

•

Customize Apps

Click to open the

Customize Apps

dialog box. You can select which sonar applications

will appear in the

Sonar Apps

menu.

Related topics

Choosing a sonar application, page 34

M3 Sonar FLS Reference Manual

Summary of Contents for M3 Sonar























































































































































































Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands

Kongsberg M3 Sonar, Reference Manual

Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands