Kongsberg M3 Sonar Reference Manual Download

Page: 33 / 182

922-20297001/1.2

Starting operation of the Sonar Head

To start operation of the M3 Sonar FLS sonar, you may need to make sure that the Sonar
Head has been discovered.

Prerequisites

• The M3 Sonar FLS software must be running.

• The sound speed has been entered in

Setup

→

System Configuration

→

Deployment

→

Master Reference

Procedure

Click

Setup

→

Connect

to start the Sonar Head.

If you see an error in the

Output Messages

window, make sure that the Sonar Head

has been discovered.

Click

Setup

→

System Configuration

→

Devices

→

Sonar Setup

Click

Discover Sonar Heads

to search for the sonar on the network.

If the Sonar Head is found, select it, then click

Use Discovered Head

A discovered Sonar Head appears in the

Online Sonar Heads

list. If the Sonar

Head does not appear, the Ethernet connection between the Sonar Processor and
Sonar Head has not been established.

Click

Close

Operating procedures

Summary of Contents for M3 Sonar























































































































































































Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands

Kongsberg M3 Sonar, Reference Manual

Search results

Summary of Contents for M3 Sonar

Reviews:

Related manuals for M3 Sonar

Brands by name

Popular brands