manualshive.com logo in svg

Kongsberg M3 Sonar, Reference Manual

Share
Download
Kongsberg M3 Sonar Reference Manual Download Page 24

22

922-20297001/1.2

Changing the frequency

You can change the frequency of the M3 Sonar FLS with the

Display Widget

.

Context

Frequency buttons are available in the

Display Widget

only if the Sonar Head is running. In

addition, these buttons will not appear in playback mode.

Procedure

1

Click the

Display Widget

icon.

This icon is located in the lower-right
corner of the sonar view.

2

Click one of the buttons to select a
frequency (in kHz).

3

Click the

Display Widget

icon to hide

the widget.

Note

You cannot select a sonar application
or change the range until you connect
to a Sonar Head (Click

Setup

→

Connect

).

Testing operation of the Sonar Head

You can test the operation of the Sonar Head by confirming that sonar data is being correctly
displayed in the

Information Widget

and sonar view. In addition, any errors will be displayed

in the

Output Messages

or

Head Status

windows.

Prerequisites

The M3 Sonar FLS software must be running.

Tip

Make sure there is sufficient disk space available to complete the survey.

M3 Sonar FLS Reference Manual

Summary of Contents for M3 Sonar























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands