manualshive.com logo in svg

Kongsberg K-Sync, Installation Manual

Share
Download
Kongsberg K-Sync Installation Manual Download Page 24

24

342741/B

Read this first

Detailed information about relevant cable specifications, termination and connectors is
provided.

Each drawing provides additional information, and may, when applicable, include
minimum specifications, connector terminations and the required number of cores.
Drawings are generally not provided for standard commercial cables. Cables fall into
three categories.

1

System cables

: System cables are provided by Kongsberg Maritime as a part of

the delivery.

2

Shipyard cables

: Shipyard cables must be provided by the shipyard doing the

installation, or the shipowner. The cables must meet the minimum specifications
provided in this publication.

3

Commercial cables

: Commercial cables may be provided by Kongsberg Maritime

as a part of the delivery. The cables may also be included with third party items
that are used with the K-Sync system.

All electronic installations and corresponding wiring must be in accordance with the
vessel's national registry and corresponding maritime authority and/or classification
society.

Note

It is very important that all cables are properly installed and correctly terminated.
Observe the relevant regulations and work standards. Always leave enough cable slack
close to system units and cabinets to allow for maintenance.

Only skilled and authorized personnel can install the K-Sync cables.

Kongsberg Maritime accepts no responsibility for damage to the system, or reduced
operational performance, when this is caused by improper wiring.

Before you install or maintain the system cables, make sure that the AC mains circuit
breaker for K-Sync and all system involved are disconnected.

KONGSBERG K-Sync Installation manual

Summary of Contents for K-Sync









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands