Kongsberg Flexview Reference Manual Download

Page: 128 / 160

126

922-20207001/1.0

Help menu

The

Help

menu allows you to view hardware and software information in the

About

Flexview

dialog box. You can also open the Flexview

Reference Manual

from this menu.

How to open

To open this menu, click the menu title.

Description

About dialog box

The

About

dialog box displays the software version of the

Flexview program. The version described in this Reference
Manual is 1.0.

User Manual

Click

User Manual

to open the Flexview

Reference Manual

in PDF format. This manual

is only applicable to the software version you are using. If you are using an older version
of software, it will not be the latest version.

Tip

You can download the latest software from

http://www.km.kongsberg.com/mesotechsoft-

ware

, and the latest manuals from

http://www.km.kongsberg.com/mesotechdocumenta-

tion

Flexview Reference Manual

Summary of Contents for Flexview

































































































































































Search results

Summary of Contents for Flexview

Reviews:

Related manuals for Flexview

Brands by name

Popular brands

Kongsberg Flexview, Reference Manual

Search results

Summary of Contents for Flexview

Reviews:

Related manuals for Flexview

Brands by name

Popular brands