Komatsu WA380-8 Operation & Maintenance Manual Download Page 8 | Manualshive

Page: 8 / 432

Komatsu WA380-8 Operation & Maintenance Manual Download Page 8

INTRODUCTION

MAIN USE OF MACHINE

This Komatsu machine is designed to be used mainly for the following work:

• Digging work
• Leveling work
• Dozing work
• Loading work

For details of the work procedure, see “RECOMMENDED APPLICATIONS (3-208)”.

DIRECTIONS OF MACHINE

(A) Front
(B) Rear
(C) Left

(D) Right
(E) Bucket
(F) Operator's seat

In this manual, the directions of the machine (front, rear, left, right) are determined according to the view from
the operator's seat in the direction of travel (front) of the machine.

VISIBILITY FROM OPERATOR'S SEAT

This machine complies with the visibility standard (ISO5006).
This machine maintains a proximity visibility of a height of 1.5 m at a point 1 m away from the outside surface of
the machine, and a visibility for a radius of 12 m.

Protective structures

This machine is equipped with a structure to protect the operator (ROPS) conforming to ISO3471.

INTRODUCTION

FOREWORD

1-6

«
...
6
7
8
9
10
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments