manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 407 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 407

Continuous mode

When  switch  is  operated  to  the  limit  of  position  (C),  the  set
maximum  flow  is  held  and  the  third  attachment  continues  the
operation even if the switch operation is stopped. This action is
called the detent control.
Use this control when the installed attachment requires contin-
uous hydraulic oil flow.
Detent control operation pilot lamp (D) lights up during the de-
tent control.
The  detent  control  is  canceled  by  any  of  the  following  opera-
tions.

• Operate the switch again.
• Turn the work equipment lock switch ON.
• Turn the starting switch key to OFF position.
• Stop the engine.
• Cancel the continuous mode on the monitor.

Proportional mode

This mode does not have the detent control function which the continuous mode has.

REMARK

The  hydraulic  oil  discharged  volume  is  in  proportion  to  the  stroke  of  the  switch  in  both  continuous  mode  and
proportional mode.

LCD UNIT

(1) Flow control mode pilot lamp (Continuous mode/Proportion-

al mode)

(2) Detent operation pilot lamp
(3) Attachment oil flow level

OIL FLOW CONTROL MODE PILOT LAMP (FIXED OIL FLOW MODE)

The  flow  control  mode  pilot  lamp  (continuous  mode)  lights  up
when the flow control of PCS is in the continuous mode.

ATTACHMENTS AND OPTIONS

HANDLE MULTIFUNCTION MONO-LEVER

6-7

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments