Komatsu WA380-8 Operation & Maintenance Manual Download Page 40 | Manualshive

Page: 40 / 432

Komatsu WA380-8 Operation & Maintenance Manual Download Page 40

Whenever  leaving  the  machine,  be  sure  to  lower  the  work
equipment to the ground, lock the work equipment by pressing
work equipment lock switch (1) (pilot lamp lights up) and stop
the  engine  by  setting  parking  brake  switch  (2)  to  ON  (opera-
tion)  position  (A).  In  addition,  lock  all  places  and  always  take
the key with you and keep it in the specified location.

EMERGENCY EXIT FROM OPERATOR'S CAB

Machines equipped with a cab have a door on the left side and a door for an emergency escape on the right
side. If the door on the left side does not open, use the right side emergency escape door.

PRECAUTIONS FOR CLEANING CAB GLASS

Clean the cab glass to ensure visibility during operation.
Make sure to clean the glass with a mop from the ground.
For the cleaning procedure, see “METHOD FOR WALK-AROUND CHECK (3-159)”.

DO NOT GET CAUGHT IN WORK EQUIPMENT

• If the clearance at the articulating portion changes and you

get caught in it, you will suffer serious personal injury or
death. Do not allow anyone to come inside the articulation
range.

• The clearance in the area around the work equipment

changes according to the movement of the link. If you are
caught, this may lead to serious personal injury or death.
Do not allow anyone near any of the rotating or telescopic
parts.

,&

GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTE-
NANCE

SAFETY

2-20

«
...
38
39
40
41
42
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands