Komatsu WA380-8 Operation & Maintenance Manual Download Page 396

Page: 396 / 432

SPECIFICATIONS

SPECIFICATIONS: WA380-8

Item

Unit

WA380-8

(in POWER mode)

Operating weight

18215

Normal load

5900

Bucket capacity

Heaped

3.35

Engine model

KOMATSU SAA6D107E-3

Rated horsepower

SAE J1995 (gross)

kW {HP} /

min

-1

{rpm}

143 {192} / 2100 {2100}

ISO 14396

143 {192} / 2100 {2100}

ISO9249 / SAE J1349 (net)

143 {191} / 2100 {2100}

A Overall length

8365

B Overall height (work equipment)

3395

C Overall height with bucket lifted up

5585

D Overall width

2765

E Min. ground clearance

455

F Bucket width

2990

G Dumpling clearance (*1)

Cutting edge [BOC tip]

2970 [2895]

H Dumpling reach (*1)

Cutting edge [BOC tip]

1080 [1110]

I Bucket dump angle (max. height)

deg.

49.5

Min. turning radius

Cutting edge [BOC tip]

7265

Center of outside tire

6320

Permissible towing load

kN { kg}

131 {13360}

Max. speed
[At lock up]

Forward

1st

km/h

6.6 [ - ]

2nd

km/h

12.4 [11.7]

3rd

km/h

22.5 [20.9]

4th

km/h

38.6 [36.1]

Reverse

1st

km/h

7.1 [ - ]

2nd

km/h

13.3 [12.4]

3rd

km/h

24.1 [22.3]

4th

km/h

37.5 [37.5]

All values with bucket S03 + BOC (S40)

SPECIFICATIONS

5-2

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Komatsu WA380-8, Operation & Maintenance Manual, Page: 396 / 432

Search results

Summary of Contents for WA380-8

Reviews: