Komatsu WA380-8 Operation & Maintenance Manual Download Page 394

Page: 394 / 432

EVERY 4500 HOURS MAINTENANCE

Maintenance for every 50, 100, 250 and 500 hours service should be performed at the same time.

METHOD FOR CLEANING KDPF

Contact your Komatsu distributor for cleaning of the KDPF.

METHOD FOR CLEANING DEF TANK

Ask your Komatsu distributor for cleaning of the DEF tank.

EVERY 8000 HOURS MAINTENANCE

Maintenance for every 50, 100, 250, 500, 1000, 2000 and 4000 hours service should be performed at the same
time.

METHOD FOR REPLACING FUEL SPRAY PREVENTION CAP

Ask your Komatsu distributor for replacement of the fuel spray prevention caps.

METHOD FOR REPLACING STARTING MOTOR

(For the machines equipped with the auto idle stop function)
Ask your Komatsu distributor for replacement of the starting motor.

EVERY 9000 HOURS MAINTENANCE

Maintenance for every 50, 100, 250, 500, 1000 and 4500 hours service should be performed at the same time.

METHOD FOR REPLACING DEF HOSE

Ask your Komatsu distributor for replacement of the DEF hose.

END OF SERVICE LIFE

• For safe dismantling of the machine at the end of service life, please contact your Komatsu distributor.

MAINTENANCE PROCEDURE

MAINTENANCE

4-74

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Komatsu WA380-8, Operation & Maintenance Manual, Page: 394 / 432

Search results

Summary of Contents for WA380-8

Reviews: