Komatsu WA380-8 Operation & Maintenance Manual Download Page 389

Page: 389 / 432

Remove nut (4) of breather assembly (3) at the top of DEF
tank, then remove cover (5).

Replace breather (6) with a new one.
When installing breather element (6), direct the surface of
TOP mark (7) towards up and install.

Install cover (5) and nut (4).

Install cover (2) with bolt (1).

EVERY 4000 HOURS MAINTENANCE

Maintenance for every 50, 100, 250, 500, 1000 and 2000 hours service should be performed at the same time.

REPLACE DEFINED LIFE PARTS

These parts change in material, wear, and deteriorate as they are aged.
Replace them every 2 years or every 4000 hours, whichever comes sooner.

MAINTENANCE

MAINTENANCE PROCEDURE

4-69

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Komatsu WA380-8, Operation & Maintenance Manual, Page: 389 / 432

Search results

Summary of Contents for WA380-8

Reviews: