manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 375 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 375

• Wrench (Width across flats: 24 mm)

1.

Loosen bolts (1) (4 pieces) and remove cover (2).

2.

Place a container under the transmission oil filter to catch
the oil.

3.

Remove transmission oil filter plug (3).

4.

Drain the oil, then tighten the plug (3).

5.

Turn  transmission  oil  filter  cartridge  (4)  counterclockwise
by  using  nut  (5)  welded  to  transmission  oil  filter  cartridge
(4) and remove it.

6.

Clean the filter holder, coat the seal surface and thread of
the new filter cartridge with transmission oil, then install it.
When  the  seal  surface  comes  into  contact  with  the  filter
holder, tighten a further 2/5 turns with the filter wrench.

7.

Check that the oil level is proper. For details, see “METHOD FOR CHECKING OIL LEVEL IN TRANSMIS-
SION CASE, ADDING OIL (4-23)”.

8.

Check the transmission oil filter for oil leakage.

METHOD FOR CLEANING TRANSMISSION BREATHER

1.

Loosen bolts (1) (4 pieces) and remove cover (2).

2.

After  removing  dirt  and  dusts  around  breather,  remove
breather (3) and immerse it in detergent liquid to clean.
While the breather is removed, take care to prevent entry
of dusts through the mounting location of the breather.

METHOD FOR CHECKING ALL TIGHTENING POINTS OF ENGINE INTAKE PIPE
CLAMPS

Ask your Komatsu distributor for checking the tightening of the clamps between the air cleaner - turbocharger -
aftercooler - engine.

MAINTENANCE

MAINTENANCE PROCEDURE

4-55

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments