Komatsu WA380-8 Page 308 Operation & Maintenance Manual Download | Manualshive

Page: 308 / 432

background image

TROUBLES AND ACTIONS

ACTIONS WHEN RUNNING OUT OF FUEL

k

k

WARNING

When starting the engine again, check safety around the engine thoroughly, and then crank the engine.

When starting the engine again after running out of fuel, fill with fuel, and bleed the air from the fuel system
before starting the engine.
For the method of bleeding air, see “METHOD FOR REPLACING FUEL PREFILTER CARTRIDGE (4-50)”.

PRECAUTIONS FOR TOWING MACHINE

k

k

WARNING

Always use the correct towing equipment and towing
method. Any mistake in the selection of the wire rope or
drawbar or the method of towing a disabled machine and
being towed may lead to serious personal injury or death.

• Always confirm that the wire rope or drawbar used for

towing has ample strength for the weight of the ma-
chine being towed.

• Never use a wire rope which has breaks in strands (A),

reduced diameter (B), or kinks (C). There is a danger
that the rope may break during the towing operation.

• Always wear leather gloves when handling the wire

rope.

• Never tow a machine on a slope.
• During the towing operation, never stand between the

towing machine and the machine being towed.

• Operate the machine slowly and be careful not to ap-

ply any sudden load to the wire rope.

• If there is a failure in the brake system, the brakes will

not work, so be extremely careful.

NOTICE

• Tow the machine only for a short distance, such as to a place for inspection and maintenance.

Do not tow the machine for a long distance.

• For details of the allowable towing capacity for this machine, see “SPECIFICATIONS (5-2)”.
• For details of the procedure for towing a disabled machine, consult your Komatsu distributor.

This machine must not be towed except in emergencies. However, if it is avoidable to tow the machine, take the
following precautions.

• When releasing the brake, secure the machine with chocks. If the wheels are not chocked, the machine

may move suddenly.

• When towing a machine, tow it at a low speed of less than 2 km/h, and for a distance of a few meters to a

place where repairs can be performed.
This method is applied only in emergencies. If the machine must be moved a long distance, use a trans-
porter.

• If it is impossible to operate the steering and brakes of the machine being towed, do not let anyone ride on

the machine.

TROUBLES AND ACTIONS

OPERATION

3-244

«
...
306
307
308
309
310
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Allied Pages: 46

Brand: Toro Pages: 40

Brand: Kubota Pages: 134

Brand: Kubota Pages: 134

Brand: Kubota Pages: 138

Brand: Kubota Pages: 144

Brand: Kubota Pages: 168

Brand: Kubota Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands