Komatsu WA380-8 Page 289 Operation & Maintenance Manual Download | Manualshive

Page: 289 / 432

background image

EXPLANATION OF AIR CONDITIONER EQUIPMENT

(1) OFF switch
(2) Auto switch
(3) Air conditioner switch
(4) Fan switch
(5) Temperature control switch

(6) FRESH/RECIRC air selector switch
(7) Vent selector switch
(8) Defroster switch
(9) Display monitor

Air conditioner monitor
(A) Air flow bar
(B) Air conditioner operation symbol
(C) Set temperature display
(D) FRESH/RECIRC selector symbol

(E) Vent display
(F) Automatic operation symbol
(G) Defroster symbol

OFF SWITCH

The OFF switch is used for stopping the fan and air conditioner.

REMARK

Even if this OFF switch is pressed, the monitor screen does not
switch to the air conditioner adjustment screen.

FAN SWITCH

Use  the  fan  switch  to  adjust  the  air  flow  from  the  fan  in  the
manual operation.
When  switch  (A)  is  pressed  while  the  air  conditioner  power
supply  is  OFF,  the  electric  power  for  the  air  conditioner  is
turned ON. At this time the air flow starts from “LOW”.

• The air flow can be adjusted to 6 levels.
• Press switch (A) to increase the air flow and press switch

(B) to decrease the air flow.

OPERATION

HANDLE AIR CONDITIONER

3-225

«
...
287
288
289
290
291
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Eoslift Pages: 12

Brand: Toro Pages: 12

Sitework Systems 22420

Brand: Toro Pages: 12

GTH-3007 Stage B

Brand: Genie Pages: 134

GTH-2506 Stage A

Brand: Genie Pages: 155

Brand: Genie Pages: 187

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands