manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 282 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 282

METHOD FOR PARKING MACHINE

k

k

 WARNING

• Avoid a sudden stop. Stop the machine gradually.
• Do not park the machine on a slope.

If  it  is  unavoidable  to  park  the  machine  on  a  slope,
place  the  machine  at  a  right  angle  to  the  slope  face,
chock  the  tires,  and  then  lower  the  bucket  to  the
ground.

• If the control lever is touched by accident, the machine

may  move  suddenly,  and  this  may  lead  to  a  serious
personal injury or death. Before leaving the operator's
seat, always lock the work equipment (the pilot lamp in
the switch lights up).

• Even if the parking brake switch is turned ON, there is

danger until the parking brake pilot lamp on the moni-
tor lights up. Keep depressing the brake pedal.

 

NOTICE
Never  use  the  parking  brake  switch  to  brake  the  machine
when the machine is traveling except in an emergency. Ap-
ply the parking brake after the machine is stopped.

1.

Release  accelerator  pedal  (1),  then  depress  brake  pedal
(2) to stop the machine.
The machine stops.

2.

Set directional lever (3) in NEUTRAL position (N).

3.

Set parking brake switch (4) to ON position (A) to apply the
parking brake.

NOTICE
Applying  the  parking  brake  automatically  sets  the
transmission to NEUTRAL.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-218

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments