manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 269 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 269

METHOD FOR AUTO-DIGGING

If the auto-kickdown and auto-digging are combined to use, the operator can operate the machine more easily.
Switch ON and OFF of the auto-kickdown on the monitor. For the method of switching, see “AUTO KICK DOWN
SETTING (3-71)”.

• When setting the auto-kickdown to ON

1) Set the auto-digging switch to ON.

2) While driving the machine forward, lower the bucket edge

to height (a) of approximately 30 cm above the ground.

3) Depress the accelerator pedal and thrust the bucket edge

into the stock pile.
The speed is shifted down to FORWARD 1st by the auto-
kickdown, and the auto-digging starts.

REMARK

• If  the  travel  speed  is  3 km/h  or  less  during  the  auto-

digging mode, the boom may rise automatically.

• If  the  gear  is  shifted  down  to  1st  by  the  kickdown

switch, the machine is set in the auto-digging mode as
well.

• When the gear speed is fixed to 1st in the manual shift

mode, if the kickdown switch is pressed, the machine
is set in the auto-digging mode.

4) If the bucket is fully tilted, the auto-digging mode is finished.

The  auto-digging  mode  can  be  canceled  by  performing  the  following  operations.  When  the  auto-digging
mode is canceled, the buzzer “beeps”.

• When the boom is raised beyond the horizontal position
• When the auto-digging switch is set to OFF
• When the boom control lever is set to “LOWER” position
• When the bucket control lever is set to “DUMP” position
• When the work equipment lock switch is pressed to lock the work equipment (the pilot lamp lights up)
• When the directional lever and directional selector switch (if equipped) are set in a position other than

FORWARD (In this case, the buzzer does not sound.)

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-205

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments