Komatsu WA380-8 Operation & Maintenance Manual Download Page 24

Page: 24 / 432

SAFETY LABELS

WARNING

Be sure that you fully understand the correct position, content and how to avoid a danger shown in the
safety labels.

Handle the warning signs and safety labels used on this machine as follows.

• Always keep the safety labels clean so that you can read it properly. When cleaning the safety labels, do

not use organic solvents or gasoline. These may cause the labels to peel off.

• If the safety labels are damaged, lost, or cannot be read properly, replace them with new ones. For details

of the part numbers for the safety labels, see this manual or the actual label, and place an order to your
Komatsu distributor.

• There are also other labels in addition to the warning signs and safety labels. Handle those labels in the

same way.

SAFETY LABELS

SAFETY

2-4

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Search results

Summary of Contents for WA380-8

Reviews:

Komatsu WA380-8, Operation & Maintenance Manual, Page: 24 / 432

Search results

Summary of Contents for WA380-8

Reviews: