manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 237 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 237

NOTICE
Do not operate the switch continuously for 1 minute or longer. Doing so can damage the air compres-
sor.

The seat height is adjusted pneumatically and in stepless.
Adjust the suspension strength and seat height by pressing the
switch.
Press left side (A) of switch: RAISE
Press right side (B) of switch: LOWER
Release the switch at desired height of the seat.
Adjustment amount: 152 mm

REMARK

When the seat is low or when the machine has not been used
for  a  while,  it  takes  time  to  raise  the  seat  to  desired  height,
since no air is in the suspension.
You  can  adjust  the  seat  to  desired  height  more  quickly  by
pressing the switch while reducing the load on the seat.

METHOD FOR ADJUSTING SEAT CUSHION IN FORE-AFTER DIRECTION

Operate the lever upward, set the seat cushion to the desired
position, then release the lever.
Fore-aft adjustment: 60 mm

METHOD FOR ADJUSTING HEADREST ANGLE

Move the headrest back and forth to set it to the desired angle.
Adjustment amount: 30 °

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-173

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments