manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 196 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 196

Trouble

Fault  hours  are  added  in  the  fault  hour  meter  and  can  not  be
deleted.
All  fault  messages  are  displayed  on  LED  (A)  as  a  collective
fault.
All fault messages can be acknowledged and deleted with but-
tons (B).
The display mode will start with one of two buttons (C).
When  grease  has  leaked  from  pressurized  safety  valve  (1),
consult your Komatsu distributor.
The  pump  has  an  automatic  level  control.  If  the  grease  level
falls below “MIN” mark, the lubrication process is stopped with
the fault message “FLL” shown on the display.
If fault message “FLL” is displayed, fill up with grease and reset
the fault with button (B).

Fault message

Display

Denotation

Explanation

Control function

Fault Low Level

The minimum level in the grease
tank has been reached.

The control unit is in the FAULT
mode. The sequence of opera-
tions is stopped.

Fault Cycle Switch

No signal from cycle switch during
pump running time.

The control unit is in the FAULT
mode. The sequence of opera-
tions is stopped.

If the fault message will appear again after the reset, consult your Komatsu distributor.

HANDLE REAR VIEW MONITOR

k

k

 WARNING

• Never operate any of the switches while traveling. If you do so, there is a danger that you may make

an error in the machine operation, or neglect to watch the travel path ahead for safety, and as a re-
sult cause a serious personal injury.

• The rear view monitor is an supporting aid for checking obstacles in the rear or surroundings. An

image appearing on the monitor is limited.
When backing up the machine, be sure to make a visual check, not relying solely on the monitor.
Never rely solely on the monitor when backing up the machine.

• An  image  on  the  rear  view  monitor  does  not  show  an  actual  distance.  Drive  the  machine  slowly,

when backing it up.

• The distortion different from the actual state appears on an image on the rear view monitor.

So, look at the center of the screen as a reference.

 

EXPLANATION OF COMPONENTS

OPERATION

3-132

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments