manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 192 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 192

SYSTEM OPERATING LAMP

The system operating lamp indicates that the controller mount-
ed on the machine is turned ON.
Lamp  (1)  lights  up  in  green  when  the  controller  is  turned  ON
and normally goes out in 5 to 6 minutes after the power for the
machine is turned OFF.
Before operating the battery disconnect switch, check that lamp
(1) is not lit.

NOTICE
If  the  battery  disconnect  switch  is  turned  OFF  while  this
lamp is lit, the data in the controller may be lost.

REMARK

• Even if the starting switch is in OFF position, the controller may operate. The lamp lights up in this case, but

it is not abnormal.

• After the starting switch has been turned off, the system operating lamp may stay lit for a long time.

In such case, consult your Komatsu distributor.

• While DEF system devices are operating, the system operating lamp lights up to return DEF to the tank.

Do not turn the battery disconnect switch to OFF position while the system operating lamp is lit.

BACKUP ALARM

This alarm sounds as soon as the machine moves in reverse to
warn people behind the machine.
When  moving  the  machine  in  reverse,  perform  the  following
procedure.

• Set the directional lever to REVERSE position (R).
• Set  the  directional  selector  switch  (if  equipped)  to  RE-

VERSE position.

• Set  the  directional  selector  switch  of  the  multifunction

mono-lever (if equipped) to REVERSE position.

HANDLING FRONT WIPER
Preventing the damage to the wiper arm bracket

NOTICE
When  tilting  wiper  arm  (1)  forward,  make  sure  that  wiper
blade (2) moves freely.

When tilting wiper arm (1) forward for cleaning cab glass, etc.,
make sure that wiper blade (2) is not locked in the arm (the bot-
tom of the blade is not caught in the arm). If locked, an abnor-
mal  external  force  may  apply  to  the  bracket  when  you  tilt  the
wiper arm forward, and the bracket may be damaged.

AUTO-GREASING

NOTICE
The auto-greasing system is used only for all connected lubrication points. The other lubrication points
have to be greased manually.

Changing the lubrication interval times

The auto-greasing system is adjusted for the normal use.

EXPLANATION OF COMPONENTS

OPERATION

3-128

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments