Komatsu WA380-8 Page 184 Operation & Maintenance Manual Download | Manualshive

Page: 184 / 432

background image

OPTIONAL POWER SUPPLY OUTLET

You can take out power of 24 V through connectors (1) and (2) at the rear left of the operator's seat.

No.

Con-

nector

No.

At key

OFF

At key ON

When en-

gine is

started

Fuse

Fuse capacity

(1)

FS6

Power

supplied

Power

supplied

Power

supplied

Fuse box A-(7)

10 A

(2)

FS7

Power not

supplied

Power

supplied

Power

supplied

Fuse box A-(12)

20 A

Since the fuse of (2) is also used for the additional front working lamp (if equipped) and beacon lamp (if equip-
ped), prevent that the current consumption of the devices used does not exceed the capacity of the fuse.

FUSE

NOTICE
When replacing the fuse, be sure to turn the starting switch to OFF position and, after confirming that
the system operating lamp is not lit, set the battery disconnect switch key to OFF position.

The fuses protect the electrical component and wiring from burning out.
If the fuse becomes corroded, or looks white powdery, or the fuse is loose in the fuse holder, replace the fuse.
Replace the fuse with the one of the same capacity.
Should the fuse is blown, investigate the cause and take necessary actions.
Inside rear console box
Loosen knobs (1) (2 places), then remove cover (2). Fuse box-
es are A, B, and C inside.

EXPLANATION OF COMPONENTS

OPERATION

3-120

«
...
182
183
184
185
186
...
»

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WA380-8

Brand: Case Pages: 41

Brand: Allied Pages: 42

Brand: Allied Pages: 48

Brand: Yanmar Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands