manualshive.com logo in svg

Komatsu WA380-8, Operation & Maintenance Manual, Page: 113 / 432

Share
Download
Komatsu WA380-8 Operation & Maintenance Manual Download Page 113

REMARK

The switches effective on each screen can be checked with the
guidance icon.
This  function  is  not  available  when  you  press  a  switch  not
marked by the guidance icon or you press the guidance icon it-
self.

AIR CONDITIONER SWITCH / NUMERIC KEYPAD

The  air  conditioner  switch  and  the  numeric  keypad  which  are
used  for  the  operation  of  the  air  conditioner  consist  of  10
switches.
For  explanation  of  each  switch,  see  “HANDLE  AIR  CONDI-
TIONER (3-224)”.
These  switches  can  be  used  as  a  numeric  keypad  to  enter  a
numeric value such as a password.
Press a desired switch to enter a numeric value 0 to 9, which is
indicated at the lower right of each switch.

• For details of other switch functions, see the explanation for each screen in “USER MENU (3-49)”.
• The confirmation sound is heard when the switch is pressed, but a reaction is taken (the switch function is

operated) when the switch is released.

USER MENU

When menu switch (1) is pressed on the standard screen while
the machine is stopped, the user menu screen is displayed to
enable you to configure and confirm machine settings.

OPERATION

EXPLANATION OF COMPONENTS

3-49

Summary of Contents for WA380-8

















































































































































































































































































































































































































































Reviews:

No comments