manualshive.com logo in svg

Komatsu PC500LC-10R, Shop Manual, Page: 511 / 758

Share
Download
Komatsu PC500LC-10R Shop Manual Download Page 511

METHOD FOR ADJUSTING MIRRORS

k

 Be sure to adjust the mirrors before starting work. If they are not adjusted properly, you cannot se-

cure the visibility and will be injured or may lead to a serious personal injury or death.

k

 The following conditions must be met before starting the work to prevent the machine from moving

during the work.

k

The machine is placed on a level ground.

k

The work equipment is lowered to the ground in secure posture.

k

The lock lever is in LOCK position.

k

The engine is stopped.

Mirror (A): Machine L.H. front mirror
Mirror (B): Machine R.H. front mirror
Mirror (C): Machine R.H. side mirror
Mirror (D): Mirror on counterweight

PROCEDURE FOR ADJUSTING MACHINE LEFT FRONT MIRROR (A)

k

 To  prevent  the  machine  from  moving  during  the  work,  make  sure  that  the  following  conditions  are

met before starting the work.

k

The machine is placed on a firm, level ground.

k

The work equipment is lowered to the ground in secure posture.

k

The lock lever is in LOCK position.

k

The engine is stopped.

Adjust the mirror so that the operator can see a person at the rear left of the machine.
1.

Adjust the mirror with your hand so that the side of the ma-
chine is reflected in the mirror as shown in the figure.

2.

Check that you can see a person at the rear left end of the
machine.

30 TESTING AND ADJUSTING

METHOD FOR ADJUSTING MIRRORS

PC500LC-10R

30-105

Summary of Contents for PC500LC-10R























































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments